ECMTuning - wiki

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.

<h1>ECMLink - Speed Density Setup</h1>
<div class="level1">

<p>
This page describes the basic process for getting your car setup for speed density operation with ECMLink.  If you need a more general speed density tutorial, then the <a href="/wiki/doku.php?id=sd101" class="wikilink1" title="sd101">Speed Density 101</a> page may be what you're looking for.  In fact, we're going to assume you already know everything off that page as we discuss items below.  So it might be a good idea to read over it even if you're already pretty familiar with SD in general.
</p>

<p>
The basic process for getting a new SD system up and going is listed here.  More details follow in the sections below.
</p>
<ol>
<li class="level1"> Connect IAT and MAP sensors to ECU</li>
<li class="level1"> Configure ECU for SD operation</li>
<li class="level1"> Dial in the VE table for your car</li>
</ol>

</div>

<h1>Connecting the Sensors</h1>
<div class="level1">

<p>
The first step is to connect your sensors to your ECU.   You'll need a GM IAT sensor and an absolute pressure sensor.  The following two sections list the supported sensors.  A good source for the GM sensors might be <a href="http://www.gmpartsdirect.com/" class="urlextern" title="http://www.gmpartsdirect.com/" rel="nofollow">GM Parts Direct</a>.  We also really like the <a href="http://www.eficonnection.com" class="urlextern" title="http://www.eficonnection.com" rel="nofollow">EFI Connection</a> for GM connectors.
</p>

<p>
For additional wiring and/or pinout information, please refer to our <a href="/wiki/doku.php?id=ecuwiringinformation" class="wikilink1" title="ecuwiringinformation">ECU Wiring Information</a> page.
</p>

</div>

<h2>Air temperature - GM IAT/AEM IAT</h2>
<div class="level2">

<span class='np_break'> </span>
<div class="table"><table class="inline">
	<thead>
	<tr class="row0">
		<th class="leftalign"> Sensor   </th><th class="leftalign"> Desc/part number  </th>
	</tr>
	</thead>
	<tr class="row1">
		<td class="leftalign"> GM IAT   </td><td class="leftalign"> GM Intake Air Temperature P/N 25036751, pig tail 12102620   </td>
	</tr>
	<tr class="row2">
		<td class="leftalign"> AEM IAT  </td><td class="leftalign"> The exact same as the GM IAT  </td>
	</tr>
</table>
<span class='np_break'> </span>
</div>
<p>
You must connect your IAT sensor to the ECU's IAT input.  This is the only input that's compatible with the speed density logic inside the ECU.
</p>

<p>
You'll want to use pin 72 (red w/blue stripe) on a 2G ECU harness or pin 8 (green w/orange stripe) on a 1G ECU harness for this.  Or, more likely, you'll want to use those wires off the MAF harness under the hood since that's where the IAT sensor is actually being installed.  <img src="/wiki/lib/images/smileys/icon_wink.gif" class="icon" alt=";-)" />  The wire colors are the same on the MAF connector as on the ECU harness.
</p>

<p>
The IAT sensor has two wires coming out of it.  Either wire can be connected to the ECU's IAT input.
</p>

<p>
The other wire should be connected to the ECU's sensor ground.  That would be pin 92 (black) on a 2G ECU harness or pin 24 (green w/black stripe) on a 1G ECU harness.  This can also be pulled from the MAF connector under the hood.  The wire colors are the same on the MAF connector as on the ECU harness.
</p>

</div>

<h2>Absolute Pressure</h2>
<div class="level2">

<span class='np_break'> </span>
<div class="table"><table class="inline">
	<thead>
	<tr class="row0">
		<th class="leftalign"> Sensor   </th><th class="leftalign"> Desc/part number  </th>
	</tr>
	</thead>
	<tr class="row1">
		<td class="col0"> GM 3-bar </td><td class="leftalign"> GM 3-bar P/N 12223861, pig tail 15305891  </td>
	</tr>
	<tr class="row2">
		<td class="leftalign"> GM 3.3-bar   </td><td class="leftalign"> GM 3.3-bar P/N 9373269, pig tail 88987997  </td>
	</tr>
	<tr class="row3">
		<td class="leftalign"> AEM 3.5-bar  </td><td class="leftalign"> AEM 30-2130-50 (50 PSIA / 3.5 Bar)  </td>
	</tr>
	<tr class="row4">
		<td class="leftalign"> AEM 5-bar  </td><td class="leftalign"> AEM 30-2130-75 (75 PSIA / 5 Bar)  </td>
	</tr>
</table>
<span class='np_break'> </span>
</div>
<p>
You wire up a pressure sensor much like you wire up any other aftermarket sensor for logging.  The details of which can get complicated because there are several different inputs you can use and several different sensors.  So it's hard to write up a COMPLETE how-to on this.
</p>

<p>
Our <a href="/wiki/doku.php?id=installnewsensor" class="wikilink1" title="installnewsensor">Aftermarket Sensor Install</a> page is a good starting point.  That page links to several other useful pages, including this example install of a <a href="/wiki/doku.php?id=gm3barinstall" class="wikilink1" title="gm3barinstall">GM 3-bar sensor on the 2G MDP</a> input.
</p>

<p>
The basic process involves the following steps:
</p>
<ol>
<li class="level1"> Select an <a href="/wiki/doku.php?id=externalsensorinput" class="wikilink1" title="externalsensorinput">available ECU input</a> you want to use</li>
<li class="level1"> Remove any existing sensor connected to that input</li>
<li class="level1"> Install the new sensor, providing any necessary power and ground connections to it</li>
<li class="level1"> Connect the sensor's output signal to the ECU's input wire you selected in step 1</li>
</ol>

</div>

<h2>Using our GM MAF Cable</h2>
<div class="level2">

<p>
If you have our GM MAF cable already, GREAT!  You can use the breakout points provided on that cable to connect your MAP sensor and IAT sensor directly to the car's wiring harness.  Our <a href="/wiki/doku.php?id=gmmafiatbaro" class="wikilink1" title="gmmafiatbaro">GM MAF IAT/Baro page</a> describes how to do this.
</p>

</div>

<h1>Configuring the Software</h1>
<div class="level1">

<p>
First, make sure you have installed the latest version of our application off our <a href="http://www.ecmtuning.com/downloads.php" class="urlextern" title="http://www.ecmtuning.com/downloads.php" rel="nofollow">downloads page</a>.  You'll want at least v3.18.182.  Anything older than that may not even connect with your ECU.
</p>

<p>
Once you have installed the latest software, you can enable speed density operation by defining three things: <br/>

</p>

<p>
Engine Displacement, MAP Sensor Location and Type, and BaseMAF type
</p>

</div>

<h2>Engine Displacement</h2>
<div class="level2">

<p>
<a href="/wiki/lib/exe/fetch.php?tok=d74765&media=http%3A%2F%2Fwww.ecmtuning.com%2Fimages%2Fforums%2Fsddata%2Fsddisplacement.png" class="media" title="http://www.ecmtuning.com/images/forums/sddata/sddisplacement.png"><img src="/wiki/lib/exe/fetch.php?tok=d74765&media=http%3A%2F%2Fwww.ecmtuning.com%2Fimages%2Fforums%2Fsddata%2Fsddisplacement.png" class="medialeft" alt="" /></a>
This one is trivial.  On the Speed Density tab, there's a text box where you need to enter your engine displacement.  The ECU uses this information to correctly calculate airflow.  More information on this process is outlined in the <a href="/wiki/doku.php?id=sd101" class="wikilink1" title="sd101">SD101 page</a>.
</p>

</div>

<h2>MAP Sensor Location and Type</h2>
<div class="level2">

<p>
<a href="/wiki/lib/exe/fetch.php?tok=c72986&media=http%3A%2F%2Fwww.ecmtuning.com%2Fimages%2Fforums%2Fsddata%2Fsdmaploc.png" class="media" title="http://www.ecmtuning.com/images/forums/sddata/sdmaploc.png"><img src="/wiki/lib/exe/fetch.php?tok=c72986&media=http%3A%2F%2Fwww.ecmtuning.com%2Fimages%2Fforums%2Fsddata%2Fsdmaploc.png" class="medialeft" alt="" /></a>
Because you can connect your MAP sensor to any number of ECU inputs, you have to tell the ECU where it can find this sensor in order to use it for SD operation.  You do this on the ECU Inputs tab in the "Pin Assignments for ECMLink Functions (ECU-side)" area.
</p>

</div>

<h2>BaseMAF Type</h2>
<div class="level2">

<p>
<a href="/wiki/lib/exe/fetch.php?tok=bf118a&media=http%3A%2F%2Fwww.ecmtuning.com%2Fimages%2Fforums%2Fsddata%2Fsdbasemaf.png" class="media" title="http://www.ecmtuning.com/images/forums/sddata/sdbasemaf.png"><img src="/wiki/lib/exe/fetch.php?tok=bf118a&media=http%3A%2F%2Fwww.ecmtuning.com%2Fimages%2Fforums%2Fsddata%2Fsdbasemaf.png" class="medialeft" alt="" /></a>
The final step is to tell the ECU to ignore incoming MAF data and calculate it from speed density data instead.  You do that on the MAFComp tab by selecting "Speed Density" as your Base MAF type.
</p>

</div>

<h1>Dialing in the VE Table</h1>
<div class="level1">

<p>
This is the "fun" part of a new SD installation.  Luckily, there are a several tips and helpers that can make this process pretty painless.  We'll add links here to other helper pages as we document them.
</p>

</div>
ECMTuning - wiki

User Tools

Site Tools

Page Tools
