This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
howto [2008/01/23 06:22] 76.100.119.159 |
howto [2024/03/15 11:16] (current) |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== How-To's ====== | ====== How-To's ====== | ||
This page is a collection of how-to's from those that have-done. | This page is a collection of how-to's from those that have-done. | ||
+ | |||
===== Hardware ===== | ===== Hardware ===== | ||
- | * SwapPlugWires | + | * [[SwapPlugWires|2G plug wire swap]] - Installing DSMLink in a car without a '95/'96 style cam angle sensor |
- | * 90ClutchCut | + | * [[90ClutchCut|Clutch cut wire on a '90 DSM]] - Installing a clutch cut (NLTS) wire in a 1990 DSM |
- | * NitrousControlDetails | + | * [[NitrousControlWiring|Basic "nitrous" controls]] - The basics of wiring up a solenoid to be control by DSMLink's "nitrous" controls |
- | * NitrousControlWiring | + | * [[NitrousControlDetails|"Nitrous" control specifics]] - More specific information about DSMLink's control of the FPR solenoid output |
- | * UseNitrousControlsForDejonToolBOVMod | + | * [[UseNitrousControlsForDejonToolBOVMod|"Nitrous" control used for BOV bypass mod]] - Describes one alternative use of DSMLink's "nitrous" controls |
- | * InnovateLC1orLM1Install | + | * [[InstallNewSensor|Install a sensor for datalogging]] - Describes how to use a non-factory sensor for datalogging (e.g., a boost sensor, a wideband kit, etc.) |
- | * 2gBaroInputWorkaround | + | * [[boostcontrol|ECU-based boost control]] - All the information you need to enable boost control from inside the ECU. |
- | * DSMLinkTPSAdjustment | + | * [[sdsetup|Speed Density Setup]] - Information on setting up your system for speed density operation |
- | * ExternalSensorInstall (boost sensor, wideband kit, etc.) | + | |
- | * ExternalSensorInput (boost sensor, wideband kit, etc.) | + | |
- | * ExternalSensorList (boost sensor, wideband kit, etc.) | + | |
===== Tuning/dial-in ===== | ===== Tuning/dial-in ===== | ||
- | * MAFTCalibrationByWBO2 | + | * [[BasicFuelAdj|Changing injectors]] - Describes how to adjust DSMLink for different injectors |
- | * MAFTCalibrationByLoggedBoost | + | * [[v3mafadjcombft|General MAF calibration]] - How-to on general MAF calibration with the V3 application |
- | * CreateVolumetricEfficiencyMap | + | * [[MAFTCalibrationByWBO2|MAFT Calibration using a WBO2]] - Describes how to calibrate a MAFT output using a WBO2 |
- | * 2GTimingIn1GECU | + | * [[MAFTCalibrationByLoggedBoost|MAFT Calibration using a boost sensor]] - Describes how to calibrate a MAFT output using a boost sensor |
- | + | * [[CreateVolumetricEfficiencyMap|Customize the VE table for your setup]] - Create a VE table more suited to your specific setup | |
- | ===== Alternate OS'es ===== | + | * [[v3tpsadj|How to dial in TPS/idle switch]] |
- | * LinuxInstall | ||
- | * MacOSInstall | ||
- | * PocketPCInstall | ||
+ | ===== Direct Access ===== | ||
+ | * [[Direct Access changes]] - Describes how to add custom changes to Direct Access | ||